• Warman SPR Rubber Lined Vertical Slurry Pump
  • Warman SPR Heavy Duty Cantilever Sump Pump
  • Warman Vertical Sump Slurry Pump
  • Warman Vertical Sump Pump Rubber Lined
  • Warman Rubber Vertical Spindle Pump

    Tobee® SPR Rubber Lined Vertical Slurry Pump

    SPECIFICATIONS:
    Size: 40~300mm
    Capacity: 7.28-1300m3/h
    Head: 3-45m
    Handing solids: 0-79mm
    Concentration: 0%-70%
    Submerged length: 500-3600mm
    Materials: Rubber, Polyurethane, Stainless steel etc
    Share
    +86 180 3203 4573
    Description

    Tobee® SPR Rubber Lined Vertical Slurry Pumps are available in various standard lengths to suit common sump depths, for very deep sumps or where high shaft speeds limit the length of the pump, a suction extension pipe can be fitted to the bottom inlet to extend the depth of the pump by up to 2 meters. Pumping is maintained even when the top inlet is not submerged, thus enabling the level of liquid to be lowered right down to the bottom inlet or the bottom of any suction extension pipe. The wet parts of SPR vertical sump pump is interchangeable with the SP series hard metal lined heavy duty sump pumps.


    Design Features:

     Bearing Assembly - The bearings, shaft and housing are generously proportioned to avoid problems associated with the operation of cantilevered shafts in the first critical speed zones.

    The assembly is grease lubricated and sealed by labyrinths; the upper is grease purged and the lower protected by a special flinger. The upper or drive end bearing is a parallel roller type whilst the lower bearing is a double taper roller with preset end float. This high performance bearing arrangement and robust shaft eliminates the need for a lower submerged bearing.

     Column Assembly - Completely fabricated from mild steel. The SPR model is elastomer covered.

     Casing - Has a simple bolt-on attachment to the base of the column. It is manufactured from a wear resistant alloy for the SP and from moulded elastomer for the SPR.

     Impeller - Double suction impellers (top and bottom entry) induce low axial bearing loads and have heavy deep vanes for maximum wear resistance and for handling large solids. Wear resistant alloys, polyurethane and moulded elastomer impellers are interchangeable. The impeller is adjusted axially within the casting during assembly by external shims under the bearing housing feet. No further adjustment is necessary.

     Upper Strainer - Drop-in metal mesh; snap-on elastomer or polyurethane for SP and SPR pumps. Strainers fit in column openings.

     Lower Strainer - Bolted metal or polyurethane for SP; moulded snap-on elastomer for SPR.

     Discharge Pipe - Metal for SP; elastomer covered for SPR. All wetted metal parts are completely rust protected.

     Submerged Bearings - None

     Agitation - An external agitator spray connection arrangement can be fitted to the pump as an option. Alternatively, a mechanical agitator is fitted to an extended shaft protruding from the impeller eye.

     Materials - Pumps can be manufactured in abrasive and corrosive resistant materials.


    Tobee® SPR Rubber Lined Vertical Slurry Pumps Performance Parameters:


    Model

    Max.Power P

    (kw)

    Clear Water Performance

    Impeller dia.

    (mm)

    Capacity Q

    Head H

    (m)

    Speed n

    (r/min)

    Max. Eff.

    (%)

    m3/h

    l/s

    40PV-SPR

    15

    17.28-39.6

    4.8-11

    4–26

    1000-2200

    40

    188

    65QV-SPR

    30

    22.5-105

    6.25-29.15

    5.5-30.5

    700-1500

    51

    280

    100RV-SPR

    75

    64.8-285

    18-79.2

    7.5-36

    600-1200

    62

    370

    150SV-SPR

    110

    108-479.16

    30-133.1

    8.5-40

    500-1000

    52

    450

    200SV-SPR

    110

    189-891

    152.5-247.5

    6.5-37

    400-850

    64

    520

    250TV-SPR

    200

    261-1089

    72.5-302.5

    7.5-33.5

    400-750

    60

    575

    300TV-SPR

    200

    288-1267

    80-352

    6.5-33

    350-700

    50

    610


    Tobee® SPR Rubber Lined Vertical Slurry Pumps Applications:


    The SPR and SP designs, manufactured in popular metric sizes, provide a simple, yet rugged range of sump pumps specially developed for: Abrasive and/or corrosive slurries, Large particle size, High slurry densities, Continuous or “snore” operations,Heavy duties demanding cantilevered shafts in minerals processing, coal preparation, chemical processing, effluent handling, sand and gravel, and almost every other tank, pit or hole-in-the-ground slurry handling situation.


    * Tobee® is a registered trademark and does not represent or is not in any way affiliated with Warman® of Weir Minerals Group. All names,numbers, symbols and descriptions are used for reference purpose only and do not imply that any pumps or parts listed is the product of Warman Pumps.

    * Tobee® SPR rubber lined vertical slurry pumps and spares are only interchangeable with Warman® SPR rubber lined vertical slurry pumps and spares.

    * This document is the property of Tobee® Pump and can be neither reproduced nor disclosed to a third party without a written authorization.